The molybdenum oxide is used as 35CrMoA, R102 like molybdenum-containing low alloy steel smelting has been successful, and has achieved significant economic benefits. In order to further explore the application possibilities of molybdenum oxide in high alloy steel smelting, we have carried out experimental research work on molybdenum oxide for low carbon and ultra low carbon stainless steel smelting. 1. Physicochemical properties of molybdenum oxide The molybdenum oxide we use has two grades: YMo50 and YMo54. The molybdenum oxide content of these two grades is 50% and 54%, respectively, and the weight of each of the blocks is between 1.0 and 5.0 kg, the specific gravity is not less than 2.5 g/cm 2 , and the moisture is not more than 0.5%. Second, thermodynamic analysis of molybdenum oxide On electric - double ladle furnace process, the smelting of stainless steel material is usually returned charge composed steels, high carbon ferrochrome, low phosphorus and returns the desired alloy steel materials. Therefore, there is a certain amount of carbon, silicon, iron, chromium and manganese in the charge. For example, for the 00Cr17Ni14Mo2 steel grade. The melting composition requirements are shown in Table 1. Table 1 00Cr17Ni14Mo2 copper part element melting content requirements element C Mn Si Cr Required content (%) 0.70~1.50 ≤1.00 ~0.40 16.50~18.50 The main component of molybdenum oxide is molybdenum dioxide. The reaction and its standard when molybdenum dioxide is contacted with [Si], [Mn], Fe(1), [C], [Cr]. Free energy changes to: [Si] + MoO 2 (s ) = [Mo] + SiO 2 (1) .................................... ①△G 1 0 =-39814-1.02T 2[Mn]+MoO 2(s) =2(MnO)+[Mo]....................................2 △G 2 0 =-35814-4.06T 3Fe (1) + MoO 2 ( s) = [Mo] + 2FeO (1) .............................. ③ △G 3 0 =23186-22.88T 2[C]+MoO (s) =[Mo]+2CO................................................4 △G 4 0 =70386-66.24T 4/3 [Cr] + MoO 2 ( s) = [Mo] +2/3 (Cr 2 O 3) .............................. ⑤ △G 5 0 =79508-103.88T The ΔG° of the above five reactions at 1400 ° C, 1500 ° C, 1600 ° C, 1700 ° C, and 1800 ° C were respectively calculated, and the results are shown in Table 2. As can be seen from Table 2, [Si], [Mn], Fe(1), [C], and [Cr] all reduce molybdenum oxide at the steelmaking temperature. As the temperature increases, the possibility of reaction of these five elements with molybdenum oxide is gradually increased by the following procedure: [Mn], Fe(1), [Si], [C], [Cr]. Table 2 △G° values ​​of five reactions at different temperatures Temperature (K) 1673 1773 1873 1973 2073 -△G 1 0 (4.1868J) -△G 2 0 (4.1868J) -△G 3 0 (4.1868J) -△G 4 0 (4.1868J) - △ G 5 0 (4.1868J) 41520 29022 15092 40434 94283 41622 28616 17380 47058 104671 41724 28210 19668 53682 115059 41826 27804 21956 60306 125447 41928 27398 24244 66930 135835 The test was carried out on a 30 t electric furnace and a 40 t ladle furnace. Third, the test steel grade and test process (1) The test steel grades include: 0Cr18Mo2, 0Cr18Mo2Ca, 00Cr17Ni14Mo2, 00Cr17Ni14Mo2 tubes. The finished Mo specifications for these four steel grades are shown in Table 3. Table 3 Finished molybdenum specifications for four steel grades Steel 0Cr18Mo12 0Cr18Mo2Ca 00Cr17Ni14Mo2 00Cr17Ni14Mo2 tube Finished product Mo range (%) 1.00~2.00 2.00~2.80 2.00~3.00 1.80~2.50 (2) Test process For the four steel grades, the original double process of electric furnace initial refining and ladle furnace refining is adopted. Moreover, according to the previous experimental experience, no amount of reducing agent is added during the reduction period of the electric furnace. 1. Method for adding molybdenum oxide Molybdenum oxide is charged into the hopper along with the charge. According to the molybdenum content of the charge, the total amount of molybdenum is about the middle limit of the specification of the finished steel product. 2, electric furnace initial refining process points During the melting period, do not blow oxygen to help dissolve or cut the material for a long time. Add 400 kg of lime in the late stage of melting. After the charge was completely dissolved, the electromagnetic stirring was turned on for 10 min, and then sampled and analyzed. The temperature is above 1600 ° C, and the double tube is oxygen decarburized. When the carbon is between 0.30% and 0.40%, the calcium carbide is added at a concentration of 3 to 4 kg/t, and an appropriate amount of C powder and Si-Fe powder are used for reduction. After the reduction slag was turned, the sample was analyzed twice. According to the analysis results, Mo and related elements were adjusted with Mo-Fe and related alloys. After the composition, temperature and slag conditions meet the requirements, the steel is tapped. 3. The main points of the refining process of the ladle furnace After the slag is removed from the ladle, 200 kg of lime is added, and the temperature is sampled and measured. When the molten steel temperature is above 1560 ° C, oxygen is refined in the vacuum position. When the oxygen concentration potential and the exhaust gas temperature drop, the oxygen consumption is determined by reference to the total oxygen consumption, and is maintained at 67 Pa for 5 min or more. Then, an alloy and a deoxidizer and an appropriate amount of lime are added. After the steel slag is well stirred, the vacuum is broken. Sampling and analysis package seat bit temperature, and add the right amount of powder or silicon aluminum - iron slag having good reducibility. Fine-tuning the ingredients according to the steel grade and analysis results. After the temperature meets the requirements, the bag is poured. Fourth, test results and discussion (1) Test results The results of the test 8 furnace steels are shown in Table 4. Table 4 Test results of eight furnace steel Preliminary furnace number Refined stove number Steel Molybdenum oxide addition amount (kg) Molybdenum oxide theory containing molybdenum (%) Actual amount of molten steel (t) Finished molybdenum (%) Molybdenum recovery rate of molybdenum oxide (%) Adding molybdenum-iron amount in electric furnace (kg) 86-1562 851-1812 0Cr18Mo2 630 1.18 30.0 1.27 94.29 - 86-1701 851-1955 0Cr18Ma2Ca 900 1.69 27.62 2.22 100 60 86-1941 851-2279 0Cr18Mo2 600 1.13 29.82 1.38 100 - 87-1903 851-2324 0Cr18Mo2 500 0.94 28.82 1.37 95.97 42 06-456 051-515 00Cr17Ni14Mo2 tube 700 1.35 29.62 2.16 86.91 100 06-444 051-502 0Cr18Mo2Ca 900 1.76 27.92 2.14 83.50 70 06-537 051-608 00Cr17Ni14Mo2 1100 2.16 30.12 2.13 80.8 150 06-495 051-551 00Cr17Ni14Mo2 1200 2.35 27.62 2.35 97.92 - (2) Discussion of test results 1. Molybdenum recovery rate of molybdenum oxide As can be seen from Table 4, the molybdenum recovery rate of molybdenum oxide charged into the hopper with the charge is between 80.8% and 100%, with an average of 92.3%. Slightly higher than the molybdenum recovery rate using ferromolybdenum. Table 5 is the statistics of molybdenum recovery rates of the same process, the same type of steel, and molybdenum-iron combined with molybdenum. As can be seen from Table 5, the recovery of molybdenum is between 80.16% and 100%, with an average of 91.32%. Table 5 Molybdenum recovery rate using ferromolybdenum (10 furnaces) Preliminary furnace number Refined stove number Steel Ferric iron addition amount (kg) Molybdenum iron theory molybdenum content (%) Actual amount of molten steel (t) Finished molybdenum (%) Molybdenum iron recovery rate (%) 97-1608 951-2023 0Cr18Mo2 500 1.11 28.62 1.52 100 95-1523 951-1820 0Cr18Ma2Ca 850 1.88 29.12 2.8 92.80 96-1339 951-1565 0Cr18Mo2 400 0.89 29.92 1.43 100 97-676 951-863 0Cr18Mo2Ca 900 2.03 28.62 2.27 90.85 97-669 951-857 0Cr18Mo2 400 0.90 27.62 1.14 82.93 96-634 951-743 0Cr18Mo2 500 1.18 29.62 1.82 83.59 96-557 951-656 0Cr18Mo2 500 1.11 28.92 1.36 90.94 97-436 951-574 0Cr18Mo2 600 1.44 27.62 1.31 80.16 96-419 951-507 0Cr18Mo2Ca 900 2.03 29.12 2.16 91.92 96-258 951-330 00Cr17Ni14Mo2 500 1.11 30.12 2.00 100 It can also be seen from Table 4 that the molybdenum molybdenum molybdenum recovery rate of the furnace without adding ferromolybium during the smelting process is above 94%. This shows that the molybdenum recovery of molybdenum oxide is relatively stable. 2. Reduction of molybdenum oxide The presence of chromium, silicon, carbon and other elements in the stainless steel charge causes the molybdenum oxide to be substantially reduced in the continuous melting of the charge and the continuous increase in the temperature of the oxidation period, which is the full melting of the test furnace. The results of the analysis and molybdenum oxide analysis were confirmed, as shown in Table 6. Table 6 Reduction of Molybdenum Oxide in Melting and Oxidation Periods of Electric Furnace Stove number Steel grade Molybdenum oxide blending amount (%) Melted molybdenum (%) Molybdenum oxide molybdenum (%) Molybdenum steel containing molybdenum in the charge (%) 86-1562 0Cr18Mo2 1.18 1.32 1.39 0.29 86-1701 0Cr18Mo2Ca 1.68 2.10 2.28 0.33 86-1941 0Cr18Mo2 1.13 1.44 1.51 0.33 87-1903 0Cr18Mo2 0.94 1.45 1.51 0.80 06-456 00Cr17Ni14Mo2 tube 1.35 2.16 2.11 0.90 06-444 0Cr18Mo2Ca 1.76 2.24 2.26 0.53 06-537 00Cr17Ni14Mo2 2.16 1.89 1.98 0.22 06-495 00Cr17Ni14Mo2 tube 2.35 2.66 2.55 0.06 In the reduction period, since the specific gravity of the molybdenum oxide is not less than 2.5 g/cm 2 , it is further reduced in the reduction slag or on the surface of the slag. 3. Effect of molybdenum oxide on the recovery of chromium The chromium content of molten steel is about 17% and the higher temperature of molten steel creates a good thermodynamic and kinetic condition for the reaction to the right. This has affected the recovery of chromium, as shown in Table 7. Table 7 Comparison of chromium recovery rates of stainless steel using molybdenum oxide and ferromolybdenum Types of Chromium recovery rate of electric furnace using molybdenum oxide (7 furnaces) Chromium recovery rate of ferromolybdenum in electric furnace (10 furnaces) Chrome back Yield (%) Average Highest Lowest 89.62 95.58 82.10 Average Highest Lowest 91.59 98.66 81.15 As can be seen from Table 7, the use of molybdenum oxide reduced the chromium recovery of the electric furnace by 1.97% compared with ferromolybdenum. Therefore, it is necessary to strengthen the reduction period, especially the reduction of slag before tapping. 4. Stability of molybdenum in molybdenum oxide in the refining process of ladle furnace After the molybdenum oxide is reduced, the molybdenum entering the molten steel is quite stable. This has been confirmed by the refining process of the ladle furnace. Table 8 shows the changes of the molybdenum of the steel of the test furnace before and after vacuum oxygen decarburization. Table 8 Changes in the molybdenum of the test furnace No. in the vacuum refining process Stove number Steel grade Vacuum molybdenum content (%) Molybdenum content after vacuum (%) Vacuum addition amount (t) 851-1812 0Cr18Mo2 1.29 1.28 1.0 851-1955 0Cr18Mo2Ca 2.26 2.23 0.9 851-2279 0Cr18Mo2 1.41 1.40 1.0 851-2324 0Cr18Mo2 1.42 1.40 1.1 051-515 00Cr17Ni14Mo2 tube 2.16 2.16 1.1 051-502 0Cr18Mo2Ca 2.18 2.15 1.08 051-608 00Cr17Ni14Mo2 2.19 2.14 1.25 051-551 00Cr17Ni14Mo2 tube 2.44 2.36 1.3 As can be seen from Table 8, the change in the molybdenum content before and after vacuum refining is mainly caused by the addition of the alloy. 5. About smelting time, power consumption and steel content (1) The time and power consumption of the test steel grade It is known from the test process that the use of molybdenum oxide does not affect the time and power consumption of the electric furnace. The data in Table 9 also illustrates this. Table 9 Comparison of time and power consumption of electric furnace stainless steel using molybdenum oxide and ferromolybdenum Types of Time and power consumption of using molybdenum oxide (7 furnaces) Time and power consumption of ferromolybdenum (10 furnaces) Average power consumption (KWh/t) Maximum power consumption (KWh/t) Minimum power consumption (KWh/t) Average smelting time (min/furnace) Maximum time (min/furnace) Shortest time (min/furnace) 536.1 603 433 206.4 261 154 588.5 661 482 232.3 283 195 (2) Quality of test steel grades The chemical composition of the finished steel of the test steel is in addition to the failure of the furnace due to equipment failure, and the finished carbon exceeds the specifications (851-1812), all of which comply with the relevant regulations. The high-strength, low-fold test and mechanical properties of the test steels all meet the relevant technical requirements. 6. Economic benefits According to the data provided by the branch, the unit price of molybdenum oxide is 18,706 yuan / t, and the unit price of molybdenum iron is 37,400 yuan / t (1989). The total tonnage of molten steel in this test was: 231.54t, the test shared 6.53t of molybdenum oxide, and the pure molybdenum of molybdenum oxide was 3.412t. 3.421 tons of pure molybdenum can replace molybdenum iron with molybdenum content of 62% as 5.577t. Therefore, this test can reduce the cost of steelmaking charging of ton steel by 373.28 yuan / t. Seven, the conclusion (1) Molybdenum oxide can be used for the smelting of low carbon and ultra low carbon stainless steel under the double furnace process of electric furnace-ladle furnace. (2) Under the test conditions, the molybdenum recovery rate of molybdenum oxide is up to 92.30%, which is slightly higher than the recovery rate of ferromolybdenum, but the recovery rate of chromium is decreased. It is necessary to strengthen the reduction of the reduction slag. (3) Molybdenum oxide is used for the smelting of low-carbon and ultra-low-carbon stainless steel, and the cost of ton steel charging is reduced by 373 yuan, which does not affect the smelting time and power consumption of the electric furnace.
The Hydraulic Press Robot is to match the hydraulic press, Automatic feeding, discharging conveying the hardward products, to raising whole line effective rate, avoid industry injury. It provide safe and precious automaticly operation, replace the manual operation, avoid to damage the hands.
It imitate human action, grab products with fixed procedures, handle items to control punch press.
Features: precision positioning, stable production quality, working rhythm is adjustable, stable running and reliable, and easy maintenance.
Manipulator of Hydraulic Drawing,Hydraulic Drawing Robot,Hydraulic Drawing feeder Shantou Sunshine Automation Equipment Co.,Ltd. , http://www.stjsrobot.com