Turbo Full Electrical Auto Blow Molding Machine Turbo Full Electrical Auto blowing machine is most advanced high speed model for bottles from 100ml to 2L bottles. It can produce all kinds of bottles below 2L, including food packaging bottles, edible oil bottles, soda and mineral water bottles, fruit juice bottles, wine bottles, cosmetics bottles and so on. It has below features: Turbo Full Electrical Auto Blow Molding Machine,Electrical Auto Blow Molding Machine,Semi Automatic Blow Molding Machine,Semi-Automatic Blow Molding Machine TAIZHOU WATON MACHINERY CO LTD , https://www.watonblowings.com
1. Examine meticulously the tire system.
The automobile nursed back to health with the soaring price of oil, and the price of oil became the subject of most commentary debates when the owners were in the air. How to let your own car to drink less oil and run more is a very practical problem.
2. Detail often check brake system.
Some vehicles will present a light drag brake, which means that the vehicle will intensify the load of the car and increase the fuel consumption. Therefore, it is necessary to check on schedule.
3 nursed back to health, swap the whole machine.
Atmospheric filters, fuel filters, oil filters, etc., must be replaced every 5,000 kilometers or more. Since the air-filtered infarct will lead to gas volume reduction, gasoline incineration will not be substantial, and low fuel oil will obey. The wear of clutch plates, clutch pressure plates, and spark plugs used for too long can also cause signs of increased fuel consumption. Therefore, they must be replaced on schedule.
4. Increase the load.
According to statistics, the load per 1,000 grams will increase by 1% fuel consumption, so it is imperative to reduce as much as possible idle debris in the trunk.
Driving skills 1. Lightly refuel, light brake, brake early.
Fighting hard in the drive, slamming and slamming on the throttle are all taboos for fuel economy. Fuel-saving experiments show that the accelerator pedal is two to three times more expensive than mid-speed driving. Therefore, it should be reasonable to reduce the extent of stepping on the accelerator when it is necessary to ensure that the car is deformed. When you see the red light or the highway, you can quickly brake the brakes to speed up, and use the engine's residual energy to make the vehicle gliding.
2. Warm up and then speed up.
The engine runs at a higher temperature than if the temperature is lower, so don't be quickened when you start the engine. You should slow down for a few minutes to allow the engine to heat up and speed up.
3. Gear shift opportunities and gear choices.
The shift opportunity will be determined as much as possible between 2500-3000 revolutions, so that it can obtain better economic efficiency under the conditions of guaranteeing energy supply. To stop the low speed and high speed, when driving a manual transmission vehicle, the high speed should be replaced in real time when the speed is constant, and the “active†form should be prevented as much as possible when driving a vehicle with an active transmission.
4. Control the economic speed of vehicles.
Economic speed refers to the most fuel-efficient driving speed. There are differences in the economic speed of various types of vehicles. It is necessary to carefully read the vehicle's elucidation book, but it is probably around 70-90 km/h. Below or above this rate, fuel consumption will rise.
5. The device restarts the running-in period.
Whether the driving method of the running-in period is accurate or not, the impact on the fuel economy of the backward policy is also great. Therefore, we must be obliged to serve the driving standard that does not exceed 80 km/h and the speed does not exceed 4,000 rpm.
Full Servo control 4 main structures: Feeding, Shifting, Clamping, Stretching.
Preform Feeding System: high speed and precisely positioning;
Preform Transfer System: double the speed of preform moving, overall simplified motion;
Mold Clamping System: reaction time is reduced to 50 percent, simple structure, long use life;
Stretch System: Servo Motor precisely control, flexible adjustment improves bottle quality.
Advanced PTO System (Pulse/Train/Output Servo Positioning Module) works on high speed positioning, with higher speed, higher noise immunity and precise positioning.
TURBO Series is high speed, stable, low noise, 500ml production 6 cavity model capacity 10,000BPH, 9 cavity model 13,000BPH.