Our PalletPal is a spring actuated level loader that makes loading and unloading pallets faster, safer and easier. It uses a system of calibrated springs and shock absorbers to lower and raise loads up to 2040 kg as boxes are added to or removed from pallets. A turntable allows nearside loading/unloading. No power or air supply is required. Pallet Handling,Pallet Lift Table,Pallet Handling Equipment,Pallet Handling Procedure Marco Lift (Ningbo) Co., Ltd. , https://www.marcolift-asia.com
So small i (micro signal: dycwesc) to teach you how to deal with and reduce brake failure! 
1, as slow as possible. When the brake of the vehicle fails, turn on the double flash warning light to control the direction. If the speed is not fast, switch the high gear to the low gear. When shifting, it is necessary to combine the handbrake. If the handbrake can't pull too slowly, it can't be tightened tightly. Otherwise, it is very likely to break the wire rope. It would be even worse!
2. If the handbrake is unsuccessful, it is necessary to try to seize it - a big foot throttle, back off the block, then hit the throttle, into the block, and perhaps there is a glimmer of hope.
3, if the downhill brake failure, observe the roadside there are no mountains (or fixed objects such as walls), friction, collision, to achieve the purpose of forced parking, to minimize damage.
4. When it fails to go uphill, it should be reduced to the middle and low gears in due course and keep enough power to drive uphill and stop at the top. If there is a backslip phenomenon, the rear of the vehicle should face the slope or safety side and turn on the headlights and emergency lights.
After successfully decelerating your vehicle and parking it, you need to do the following things: 
1, set up a tripod. If it is on a regular road, a warning sign should be set at 50 meters to 100 meters behind the vehicle. On the highway, a warning sign should be set at 150 meters behind the vehicle. In case of rain and fog, You have to increase the distance to 200 meters.
2. The evacuation of the vehicle personnel to a safe location. After placing the warning sign on the vehicle, the driver and passengers must evacuate to a safe area outside the guardrail and cannot stay on the expressway, otherwise it is easy to have a second accident.
3, call 4S shop called rescue. The car can not continue to drive, call the 4S shop, and some 4S stores will rush to the scene the first time after asking the symptoms, and then to the 4S shop after the car to the 4S shop to judge and deal with. If an accident occurs during emergency treatment, call the insurance company that is insured at the first time.
How to avoid the brake failure? The first car network small i (micro signal: dycwesc) summed up the following four ways to deal with: 
  1, check the amount of brake fluid
Insufficient brake fluid will cause a decrease in braking force. The owner can open the engine compartment cover to check if the brake fluid is between the MAX and MIN scales of the brake fluid reservoir (usually located in the upper right corner of the engine compartment). If it is lower than this tick, replace it as soon as possible.
2, check the thickness of the brake pads
The thickness of a new brake pad is generally 1.5cm. When the thickness is only about 0.5cm, it needs to be replaced. In addition, pay attention to check the brake disc or brake drum wear, as long as there are dents to be processed.
3, check the brake fluid moisture content
Brake fluid has a high boiling point, usually around 260°C. If it is in hot weather, the brake system is used frequently, the vehicle driving conditions, etc., will cause the brake fluid to absorb water, as long as the inhaled water reaches 2.5%, you need to replace the new brake fluid. Check the brake fluid moisture content best to the professional repair shop inspection.
4, do not mix brake fluid
When the vehicle is traveling normally for more than 2 years or 40,000 kilometers, it is necessary to replace the brake oil. However, if the brand is different from the brand of brake oil used before, the original brake oil must be radiated before using the new brand. . Note that some of the market's inferior brake fluids are carefully selected.
In short, there are many causes of brake failure. It may be due to negligence on the maintenance of the car, or it may be due to improper operation. The owner of the car usually must not only look to see the appearance of the vehicle, but must develop good driving habits. It is also a good way to avoid brake failure.
When your car encounters a brake failure do you know what to do?
When driving, the driver’s fear is that if the brake suddenly fails, the consequences are disastrous. A few days ago, on State Road 316, Dawu Road in Shaowu, the driver of Zhou, the driver of the vehicle, caused the brake to malfunction due to vehicle overload and collided with the small passenger car traveling in the same direction in front, causing two vehicles to be damaged and one person seriously injured. Therefore, "brake failure" is the biggest hidden killer.   When you find that the brakes have suddenly failed in the drive, what should you do? This time, you must keep calm and not panic! Using the following methods may ease the severity of the accident.