Flow Meter Mechanical Flow Meter, Pneumatic Check Valve, Turbine Water Meter, Liquid Flow Meter Shanghai Jiasong Machine Co., Ltd , http://www.fuel-dispenser-parts.com
On December 26, the 2010 dealership conference of Dongfeng Commercial Vehicle Company was held in Zhengzhou International Convention and Exhibition Center. As of December 25, Dongfeng Commercial Vehicle Co., Ltd. Shiyan headquarters domestic heavy truck domestic sales of 81,463, the target of 108,500 vehicles in 2010, an increase of 32%, the market share from the 9.7% to 13.5%. By 2012, the company's headquarters will achieve sales of 80,000 D310 Dongfeng Tianlong heavy trucks and 60,000 D530 Dongfeng Tianjin trucks , building three independent branded engines.
At the same time, the reporter learned that it is expected that by the end of 2009, Dongfeng Commercial Vehicle Company will sell a total of 190,000 vehicles, and the 2010 target will be 200,000.
Dongfeng Commercial Vehicles Headquarters Heavy Trucks Locked to 108,500 Next Year
What are Flow meters?
A Flow Meter is an instrument used to measure linear, nonlinear, mass or volumetric flow rate of a liquid or a gas.
Flow meters: Quality oval gear flowmeter, positive displacement flow meter, turbine flow meter, flow transducer or a flow sensor.
Low cost flow meters, high pressure flow meters,
stainless steel flow meters, plastic flow meters, OEM flow meters, high
viscosity flow meters, acid flow meters, alkali flow meters, hydraulic
flow meters, oil flow meters, fuel flow meters, beer and water flow
meters are all possible. With our chemically resistant, high accuracy
digital flow meters with pulse outputs, we can handle almost anything.
For hazardous areas some of these can be considered as simple apparatus.
Our
process control and measuring instruments can monitor and/or display :
total, batch size, flow rate, switch, consumption and 4-20mA or 10 volt
analogue loops. The batching instruments can be used for dispensing,
totaliser, accumulated totaliser, flow rate, dispense amount as well as
full process monitoring.
The Oval gear, positive
displacement and Turbine flow meters produced by Titan are designed and
manufactured to ISO9001 and calibrated to an uncertainty of ±0.25%.
With over thirty years of experience in the production of flowmeters our
team can offer either an of the shelf meter or fully bespoke flow
products designe for a particular application whether it is a low cost
OEM flow solution or a specialist flowmeter in exotic materials.
Installation Cautions for Flowmeters
In
liquid service, be sure that the flowmeter is installed such that it
remains full of liquid, because gas/vapor in the flowmeter can alter its
geometry and adversely affect accuracy.
In gas/vapor service, be sure that the flowmeter is installed such that the flow meter remains full of gas/vapor, because liquid in the flowmeter can alter its geometry and adversely affect accuracy.
Disturbances
located upstream of the flowmeter, such as pipe elbows and control
valves, can adversely affect measurement accuracy, because the flow meter may not be able to accurately measure disturbed flow streams. Be sure
to locate control valves downstream of the flowmeter so their flow
disturbances are not introduced directly into the flowmeter. Also, be
sure to properly design the upstream and downstream piping with
sufficient straight run to remove disturbances that can affect
measurement accuracy.
Be especially careful
when flow is two-phase, such as liquid/gas flow and liquid/solid flow,
because these flows can adversely affect the accuracy of many flow meters. Be careful because some flowmeters can become plugged and stop working in liquid/solid flow streams.
Application Cautions for Flowmeters
Each
type of flowmeter has its own specific applications and installation
constraints. There is no "one size fits all" flowmeter. The way to
select the right flowmeter is to use the application as your guide, not
the technology. Many of these technologies will all work well on many
applications. If you start with the application, you can select the
technology you wish to use based on accuracy, cost, durability and
reliability, rather than trying to make the technology you chose fit the
application you have.