Common copper oxide minerals are primarily: malachite (CuC0 3 · Cu (OH) 2, copper 57.4%, density of 4g / cm 3, hardness 4); azurite (azurite, 2CUC0 3 .Cu (OH) 2 , containing 55.2% copper, density 4g/cm 3 , hardness 4). Followed by: cyanite (CuSi0 3 · 2H 2 0, copper containing 36.2%, density 2 ~ 2.2g / cm 3 , hardness 2 ~ 4) and cuprite (CU 2 0, containing 88.8% copper, density 5.8 ~ 6.2 g/cm 3 , hardness 3.5 to 4). Fatty acids collector of non-ferrous metal oxide minerals having good collector resistance, but poor selectivity (especially when the gangue mineral is carbonate), not easy to improve concentrate grade. Among the xanthate collectors, only high-grade xanthate has a certain catching effect on non-ferrous metal oxide minerals. However, without vulcanization, flotation of copper oxide ore directly with xanthate has not been applied in the industry due to high cost. The methods that have been applied in practice are: 1. Vulcanization method - the most common, simple process, any copper oxide ore that can be vulcanized can be floated by this method. The oxidized ore after vulcanization has the property of sulfide ore and can be floated with xanthate. Malachite and azurite are easily sulfided with sodium sulfide, while chrysocolla and cuprite are more difficult to vulcanize. The amount of sodium sulfide during vulcanization can reach 1~2kg/(t ore). Because the vulcanizing agent such as sodium sulfide is easy to oxidize, the action time is short, the formed vulcanized film is not stable, and the strong agitation is easy to fall off, so it should be added in batches without adding pre-mixing and directly added to the first dregs of the flotation machine. When vulcanizing, the lower the pH of the slurry, the faster the vulcanization. When there are many slime and need to be dispersed, a dispersing agent should be added, usually with water glass. Collectors are generally mixed with butyl xanthate or with black medicine. The pH of the pulp is usually kept at about 9, and when it is too low, lime can be added in an appropriate amount. 2, organic acid flotation method - organic acids and their soaps can be well floated malachite and azurite. This method can be used when the gangue mineral is not a carbonate mineral. Otherwise, the flotation will be deactivated. When a large amount of gangue contains buoyant iron, manganese minerals, will have the same effect, that the flotation is deteriorated. When an organic acid with a flotation collector, generally also add sodium carbonate, sodium silicate, phosphate inhibitor as gangue and the slurry adjusting agent. There are also examples of mixed application of vulcanization and organic acid flotation. Sodium sulfide and xanthate are used to float copper sulfide and partial copper oxide, and then the residual copper oxide is floated with organic acids. 3. Leaching-precipitation-flotation method—Used when both the vulcanization method and the organic acid method cannot obtain satisfactory results. The method utilizes copper oxide minerals to dissolve relatively easily, and the oxidized ore is first leached with sulfuric acid, then replaced with iron powder, and precipitated metal copper, and the precipitated copper is floated by flotation. The method should first be ground to the monomer according to the particle size of the mineral inlay, (-200 mesh accounts for 40% to 80%). The leachate is a 0.5% to 3% dilute sulfuric acid solution, and the amount of acid varies with the ore property of 2.3 to 45 kg / (t ore). For difficult-to-lead ore, tempering can be carried out by heating (45-70 ° C). Flotation is carried out in an acidic medium, and the collector is treated with cresol black or double xanthate. The undissolved copper sulfide mineral and the precipitated metal copper float together and enter the flotation concentrate. 4, ammonia leaching ~ sulfide precipitation ~ flotation method - such as ore contains a large amount of alkaline gangue, the use of acid leaching is large, the cost is too high. The method finely grinds the ore, adds sulfur powder, and then ammonia leaching. During the leaching process, the copper ions in the copper oxide ore react with NH3 and CO2, and are precipitated by sulfur ions to become new copper sulfide particles. The ammonia is evaporated and recovered, and the copper sulfide is floated. The pulp pH is 6.5-7.5, and a good index can be obtained by using the flotation agent of the general copper sulfide ore. This method should pay attention to the recovery of ammonia, otherwise it will cause environmental pollution. 5, segregation - flotation - essence ore particle size with the appropriate 2% to 3% of the coal powder, 1% to 2% of the salt mixture, reduction chlorination roasting between 700 ~ 800 ℃, generating Cu The chloride, which is volatilized from the ore, is reduced to metallic copper in the furnace and adsorbed on the coal particles, and then separated from the gangue by flotation. This method is suitable for the treatment of refractory copper oxide ore, especially the refractory copper oxide ore with more mud, combined with copper accounting for more than 30% of total copper, and ore containing a large amount of chrysocolla and copper. When comprehensively recovering gold, silver and other rare metals, the separation method is superior to the leaching-flotation method. The disadvantage is that the heat energy is large and the cost is high. 6. Flotation of mixed copper ore - The flotation process of mixed copper ore should be determined according to the test. The process of simultaneous flotation of oxidized minerals and sulfide minerals after vulcanization can be used. Then choose the process of oxidizing minerals. At the same time, the process conditions of flotation of copper oxide minerals and copper sulfide minerals are basically the same as those of flotation oxidized minerals, but the amount of sodium sulfide and collector should be reduced correspondingly with the decrease of oxide content in the ore. Foreign copper oxide ore uses two processes: vulcanization flotation and acid leaching-precipitation-flotation.
Product Description
Double Roll Crusher is designed for oil processing enterprises to handle large particles (soybean, peanut) oil crops in the first stage. Crushing effect direct impact on the quality and yield of the rolling billet, crusher is the key equipment of grease pre-treatment section. The machine can meet the crushing needs of daily processing capacity during 20T-1500T. Full set of large single motor drive crusher are designed on the basis of assimilation and introduction of imported technology, but the technical indicators exceed the level of similar products. The machines have been used for large oil processing enterprises in many countries. Soy Bean Crusher Machine,Oil Seeds Material Crushing Machine,Plastic Crusher Machine,Cone Crusher Machine Hebei Huipin Machinery Co.,LTD , https://www.oilpresschina.com
Daily processing capacity: 500T/D (Crushing strength 1/4-1/8 adjustable)
Features:
1. Two motors drive
2. Synchronized use of digital reducer for roller gap adjustment
3. Roll feeder, evenly distributed feeding
4. Synchronized two-stage magnetic separator and automatic feed gate
5. Stable and reliable high-tensile frame
6. High-alloy crushing roller
7. Automatic drive belt tension mechanism
8. Imported bearing and independent bearing block
